eMaxMobileApp

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.

This version 1.67 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now

All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11

new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7

new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button


new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)


new in version 1.62 (21.03.23):
- minor optimizations and bug fixes


new in version 1.61 (02.03.23):
- minor optimizations and bug fixes


new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added


new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)


new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)


new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added


new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types


new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units


new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.

This version 1.65 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now

All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

new in version 1.66 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button

new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)

new in version 1.62 (21.03.23):
- minor optimizations and bug fixes

new in version 1.61 (02.03.23):
- minor optimizations and bug fixes

new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added

new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)

new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)

new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added

new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types

new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units

new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)

new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units

new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0

new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0

new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)

new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)

new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)

new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.

This version 1.63 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.

All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)

new in version 1.62 (21.03.23):
- minor optimizations and bug fixes

new in version 1.61 (02.03.23):
- minor optimizations and bug fixes

new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added

new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)

new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)

new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added

new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types

new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units

new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)

new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units

new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0

new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0

new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)

new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)

new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)

new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo

new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0

new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8

ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added

ver. 1.42 (17.04.21):
- new battery type BT-E8016 added

ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.

This version 1.51 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DUE80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units

new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0

new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0

new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)

new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)

new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)

new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo

new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0

new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8

ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added

ver. 1.42 (17.04.21):
- new battery type BT-E8016 added

ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)

ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.

This version 1.51 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

Special to DUE80X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

Special to DUE7000 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DUEP800 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, light functionality) could be used in the license free version.

new in version 1.51 (29.03.22):
-update to newest firmware versions 4.4.7 for DUE50X0

new in version 1.50 (15.03.22):
-update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
-update to newest firmware versions 4.9.3 for DUE80X0

new in version 1.49 (22.02.22):
-32 teeth chainring size added for DUEP800 (EP8)

new in version 1.48 (24.12.21):
-update to newest firmware versions 4.1.8 for DUEP800 (EP8)

new in version 1.47 (25.11.21):
-update to newest firmware versions 4.1.7 for DUEP800 (EP8)

new in version 1.46 (18.11.21):
-optimization for EP8-RS
- typo

new in version 1.45 (07.09.21):
-update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0

new in version 1.44 (03.06.21):
-update to newest firmware version 4.1.5 for EP8

ver. 1.43 (05.05.21):
-chainring & rear sprocket size for DUE5xxx and DUE6xxx added

ver. 1.42 (17.04.21):
-new battery type BT-E8016 added

ver. 1.41 (11.04.21):
-new battery types added
-bugfix (profile 2 EP8-RS default translation error)

ver. 1.40 (06.04.21):
-update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
-update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
-update to fw. 4.7.2 for DUE7000
-update to fw. 4.1.4 for EP8
-profiles added for EP8/EP8-RS
-reduced max. speed for EP8 added
-smallest sprocket for EP8 set to 10 (instead of 11)
-dark mode issue on light settings solved

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.

This version 1.50 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

Special to DUE80X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

Special to DUE7000 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DUEP800 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, light functionality) could be used in the license free version.

new in version 1.50 (15.03.22):
-update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
-update to newest firmware versions 4.9.3 for DUE80X0

new in version 1.49 (22.02.22):
-32 teeth chainring size added for DUEP800 (EP8)

new in version 1.48 (24.12.21):
-update to newest firmware versions 4.1.8 for DUEP800 (EP8)

new in version 1.47 (25.11.21):
-update to newest firmware versions 4.1.7 for DUEP800 (EP8)

new in version 1.46 (18.11.21):
-optimization for EP8-RS
- typo

new in version 1.45 (07.09.21):
-update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0

new in version 1.44 (03.06.21):
-update to newest firmware version 4.1.5 for EP8

ver. 1.43 (05.05.21):
-chainring & rear sprocket size for DUE5xxx and DUE6xxx added

ver. 1.42 (17.04.21):
-new battery type BT-E8016 added

ver. 1.41 (11.04.21):
-new battery types added
-bugfix (profile 2 EP8-RS default translation error)

ver. 1.40 (06.04.21):
-update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
-update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
-update to fw. 4.7.2 for DUE7000
-update to fw. 4.1.4 for EP8
-profiles added for EP8/EP8-RS
-reduced max. speed for EP8 added
-smallest sprocket for EP8 set to 10 (instead of 11)
-dark mode issue on light settings solved

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.

This version 1.49 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

Special to DUE80X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

Special to DUE7000 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DUEP800 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, light functionality) could be used in the license free version.

new in version 1.49 (22.02.22):
-32 teeth chainring size added for DUEP800 (EP8)

new in version 1.48 (24.12.21):
-update to newest firmware versions 4.1.8 for DUEP800 (EP8)

new in version 1.47 (25.11.21):
-update to newest firmware versions 4.1.7 for DUEP800 (EP8)

new in version 1.46 (18.11.21):
-optimization for EP8-RS
- typo

new in version 1.45 (07.09.21):
-update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0

new in version 1.44 (03.06.21):
-update to newest firmware version 4.1.5 for EP8

ver. 1.43 (05.05.21):
-chainring & rear sprocket size for DUE5xxx and DUE6xxx added

ver. 1.42 (17.04.21):
-new battery type BT-E8016 added

ver. 1.41 (11.04.21):
-new battery types added
-bugfix (profile 2 EP8-RS default translation error)

ver. 1.40 (06.04.21):
-update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
-update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
-update to fw. 4.7.2 for DUE7000
-update to fw. 4.1.4 for EP8
-profiles added for EP8/EP8-RS
-reduced max. speed for EP8 added
-smallest sprocket for EP8 set to 10 (instead of 11)
-dark mode issue on light settings solved

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.

This version 1.48 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

Special to DUE80X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

Special to DUE7000 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DUEP800 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, light functionality) could be used in the license free version.

new in version 1.48 (24.12.21):
-update to newest firmware versions 4.1.8 for DUEP800 (EP8)

new in version 1.47 (25.11.21):
-update to newest firmware versions 4.1.7 for DUEP800 (EP8)

new in version 1.46 (18.11.21):
-optimization for EP8-RS
- typo

new in version 1.45 (07.09.21):
-update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0

new in version 1.44 (03.06.21):
-update to newest firmware version 4.1.5 for EP8

ver. 1.43 (05.05.21):
-chainring & rear sprocket size for DUE5xxx and DUE6xxx added

ver. 1.42 (17.04.21):
-new battery type BT-E8016 added

ver. 1.41 (11.04.21):
-new battery types added
-bugfix (profile 2 EP8-RS default translation error)

ver. 1.40 (06.04.21):
-update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
-update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
-update to fw. 4.7.2 for DUE7000
-update to fw. 4.1.4 for EP8
-profiles added for EP8/EP8-RS
-reduced max. speed for EP8 added
-smallest sprocket for EP8 set to 10 (instead of 11)
-dark mode issue on light settings solved

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.

This version 1.45 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

Special to DUE80X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

Special to DUE7000 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

Special to DUEP800 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, light functionality) could be used in the license free version.

new in version 1.45 (07.09.21):
-update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0

new in version 1.44 (03.06.21):
-update to newest firmware version 4.1.5 for EP8

ver. 1.43 (05.05.21):
-chainring & rear sprocket size for DUE5xxx and DUE6xxx added

ver. 1.42 (17.04.21):
-new battery type BT-E8016 added

ver. 1.41 (11.04.21):
-new battery types added
-bugfix (profile 2 EP8-RS default translation error)

ver. 1.40 (06.04.21):
-update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
-update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
-update to fw. 4.7.2 for DUE7000
-update to fw. 4.1.4 for EP8
-profiles added for EP8/EP8-RS
-reduced max. speed for EP8 added
-smallest sprocket for EP8 set to 10 (instead of 11)
-dark mode issue on light settings solved

ver. 1.39 (31.01.21):
-integration of new motor firmware version 4.1.2 for EP8
-extended light indication for EP8 (off/manual/on & max. power)
-chainring - size and sprocket size with all possible correct values now for EP8
-correction of indication of motor firmware version
-correction of minor text errors

ver. 1.38 (26.11.20):
-new battery type BT-E8036 added
-special settings (derailleur type, etc.) added for DUEP800

ver. 1.36 (08.11.20):
-partial compatibility with new firmware versions added (with warning) DUE50X0 [4.4.2], DUE61X0 [4.6.0], DUE7000 [4.6.0], DUE80X0 [4.9.0], DUEP800 [4.1.1]
-licence placeholdertext in darkmode improved (grey)
-new battery types added
-correction of AS - settings
-optimized "dark mode" handling for licence key entry boxes
-light activating functionality added
-motor mounting angle added
-optimized country specific decimal characters for total distance (odd)

ver. 1.35 (31.08.20):
-integration of DUEP800: compatibility with motor firmware 4.0.0 - 4.0.2 (USA - modification and wheel circumference modification)
-minor bug fixing and optimizations

ver. 1.34 (13.07.20):
-DUE80X0: compatibility with newest motor firmware 4.8.0

ver. 1.33 (18.05.20):
-6100, 6110, 6180 and 7000 series drive units with motor firmware 4.4.0 - 4.5.0 accepted
-6001, 6010, 6050 series drive units with current motor firmware 3.4.7 accepted
-6002, 6012 series drive units with current motor firmware 3.4.0 accepted
-5000, 5080 series drive units with current motor firmware 4.2.0 - 4.3.0 accepted

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to process a speed tuning with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.

This version 1.38 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE800X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

Special to DUE80X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

Special to DUE7000 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

- new in version 1.38 (26.11.2020):
-- new battery type BT-E8036 added
-- special settings (derailleur type, etc.) added for DUEP800

- new in version 1.36 (08.11.2020):
-- partial compatibility with new firmware versions added (with warning) DUE50X0 [4.4.2], DUE61X0 [4.6.0], DUE7000 [4.6.0], DUE80X0 [4.9.0], DUEP800 [4.1.1]
-- licence placeholdertext in darkmode improved (grey)
-- new battery types added
-- correction of AS - settings
-- optimized "dark mode" handling for licence key entry boxes
-- light activating functionality added
-- motor mounting angle added
-- optimized country specific decimal characters for total distance (odd)

- new in version 1.35 (31.08.2020):
-- integration of DUEP800: compatibility with motor firmware 4.0.0 - 4.0.2 (USA - modification and wheel circumference modification)
-- minor bug fixing and optimizations

- new in version 1.34 (13.07.2020):
-- DUE80X0: compatibility with newest motor firmware 4.8.0

- new in version 1.33 (18.05.2020):
-- 6100, 6110, 6180 and 7000 series drive units with motor firmware 4.4.0 - 4.5.0 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- 6001, 6010, 6050 series drive units with current motor firmware 3.4.7 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- 6002, 6012 series drive units with current motor firmware 3.4.0 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- 5000, 5080 series drive units with current motor firmware 4.2.0 - 4.3.0 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- adjustment of max. assist ratio value for DUE to 250%


- new in version 1.32 (26.04.2020):
-- "motor performance settings" and "special settings" added to DUE7000 drive unit
-- optimization and correction for DUE50X0

- new in version 1.31 (31.03.2020):
-- optimization and correction for DUE50X0
-- minor fixes and improvements

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to process a speed tuning with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.

This version 1.36 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE800X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

Special to DUE80X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

Special to DUE7000 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

- new in version 1.36 (08.11.2020):
-- partial compatibility with new firmware versions added (with warning) DUE50X0 [4.4.2], DUE61X0 [4.6.0], DUE7000 [4.6.0], DUE80X0 [4.9.0], DUEP800 [4.1.1]
-- licence placeholdertext in darkmode improved (grey)
-- new battery types added
-- correction of AS - settings
-- optimized "dark mode" handling for licence key entry boxes
-- light activating functionality added
-- motor mounting angle added
-- optimized country specific decimal characters for total distance (odd)

- new in version 1.35 (31.08.2020):
-- integration of DUEP800: compatibility with motor firmware 4.0.0 - 4.0.2 (USA - modification and wheel circumference modification)
-- minor bug fixing and optimizations

- new in version 1.34 (13.07.2020):
-- DUE80X0: compatibility with newest motor firmware 4.8.0

- new in version 1.33 (18.05.2020):
-- 6100, 6110, 6180 and 7000 series drive units with motor firmware 4.4.0 - 4.5.0 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- 6001, 6010, 6050 series drive units with current motor firmware 3.4.7 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- 6002, 6012 series drive units with current motor firmware 3.4.0 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- 5000, 5080 series drive units with current motor firmware 4.2.0 - 4.3.0 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- adjustment of max. assist ratio value for DUE to 250%


- new in version 1.32 (26.04.2020):
-- "motor performance settings" and "special settings" added to DUE7000 drive unit
-- optimization and correction for DUE50X0

- new in version 1.31 (31.03.2020):
-- optimization and correction for DUE50X0
-- minor fixes and improvements

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.

This version 1.35 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE800X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

Special to DUE80X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

Special to DUE7000 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

- new in version 1.35 (31.08.2020):
-- integration of DUEP800: compatibility with motor firmware 4.0.0 - 4.0.2 (USA - modification and wheel circumference modification)
-- minor bug fixing and optimizations

- new in version 1.34 (13.07.2020):
-- DUE80X0: compatibility with newest motor firmware 4.8.0

- new in version 1.33 (18.05.2020):
-- 6100, 6110, 6180 and 7000 series drive units with motor firmware 4.4.0 - 4.5.0 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- 6001, 6010, 6050 series drive units with current motor firmware 3.4.7 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- 6002, 6012 series drive units with current motor firmware 3.4.0 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- 5000, 5080 series drive units with current motor firmware 4.2.0 - 4.3.0 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- adjustment of max. assist ratio value for DUE to 250%


- new in version 1.32 (26.04.2020):
-- "motor performance settings" and "special settings" added to DUE7000 drive unit
-- optimization and correction for DUE50X0

- new in version 1.31 (31.03.2020):
-- optimization and correction for DUE50X0
-- minor fixes and improvements

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.

This version 1.33 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE800X0 motors, now DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

Special to DUE80X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

Special to DUE7000 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.

- new in version 1.33 (18.05.2020):
-- 6100, 6110, 6180 and 7000 series drive units with motor firmware 4.4.0 - 4.5.0 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- 6001, 6010, 6050 series drive units with current motor firmware 3.4.7 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- 6002, 6012 series drive units with current motor firmware 3.4.0 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- 5000, 5080 series drive units with current motor firmware 4.2.0 - 4.3.0 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- adjustment of max. assist ratio value for DUE to 250%


- new in version 1.32 (26.04.2020):
-- "motor performance settings" and "special settings" added to DUE7000 drive unit
-- optimization and correction for DUE50X0

- new in version 1.31 (31.03.2020):
-- optimization and correction for DUE50X0
-- minor fixes and improvements

- new in version 1.30 (01.03.2020):
-- 6100, 6110, 6180 and 7000 series drive units with current motor firmware 4.4.0 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- 6001, 6010, 6050 series drive units with current motor firmware 3.4.7 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- 6002, 6012 series drive units with current motor firmware 3.4.0 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- 5000, 5080 series drive units with current motor firmware 4.2.1 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- indication and individual programming of lighting time on special settings view
-- indication and individual programming of chainring size on special settings view
-- indication and individual programming of smallest rear sprocket size on special settings view
-- indication and programming of derailleur type on special settings view
-- typo in German version "Verbindung zum Fahrrrad" (Fahrrrad with 3 r) on main view
-- correction of line shifting when Bluetooth device name is empty on bike information view
-- warning message with link to documentation when ?.?.? on display firmware
-- indication of motor type, display type, battery type on bike information view
-- indication of total distance on bike information view

TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.

This version 1.31 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE800X0 motors, now DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

Special to DUE800X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

- new in version 1.31 (31.03.2020):
-- optimization and correction for DUE50X0
-- minor fixes and improvements

- new in version 1.30 (01.03.2020):
-- 6100, 6110, 6180 and 7000 series drive units with current motor firmware 4.4.0 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- 6001, 6010, 6050 series drive units with current motor firmware 3.4.7 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- 6002, 6012 series drive units with current motor firmware 3.4.0 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- 5000, 5080 series drive units with current motor firmware 4.2.1 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- indication and individual programming of lighting time on special settings view
-- indication and individual programming of chainring size on special settings view
-- indication and individual programming of smallest rear sprocket size on special settings view
-- indication and programming of derailleur type on special settings view
-- typo in German version "Verbindung zum Fahrrrad" (Fahrrrad with 3 r) on main view
-- correction of line shifting when Bluetooth device name is empty on bike information view
-- warning message with link to documentation when ?.?.? on display firmware
-- indication of motor type, display type, battery type on bike information view
-- indication of total distance on bike information view

TAKE CARE: For increasing motor max. support speed an additional license key is necessary. See also www.eMax-Tuning.com.

This version 1.30 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE800X0 motors, now DUE7000, DUE6XXX and DUE50X0 drive units are supported too.

Special to DUE800X0 drive units:
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

- new in version 1.30 (01.03.2020):
-- 6100, 6110, 6180 and 7000 series drive units with current motor firmware 4.4.0 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- 6001, 6010, 6050 series drive units with current motor firmware 3.4.7 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- 6002, 6012 series drive units with current motor firmware 3.4.0 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- 5000, 5080 series drive units with current motor firmware 4.2.1 are accepted to modify destination country and wheel circumference for increasing motor max. support speed
-- indication and individual programming of lighting time on special settings view
-- indication and individual programming of chainring size on special settings view
-- indication and individual programming of smallest rear sprocket size on special settings view
-- indication and programming of derailleur type on special settings view
-- typo in German version "Verbindung zum Fahrrrad" (Fahrrrad with 3 r) on main view
-- correction of line shifting when Bluetooth device name is empty on bike information view
-- warning message with link to documentation when ?.?.? on display firmware
-- indication of motor type, display type, battery type on bike information view
-- indication of total distance on bike information view

This version 1.22 for STEPS8xxx drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
All "motor performance settings" and "special settings" (change of gear type, change of remaining light time) could be used in the license free version.
For increasing motor max. support speed an additional license key is necessary. See also www.eMax-Tuning.com.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

- new in version 1.22:
-- added additional information about battery state on "bike information" - view ("overall condition" and "total charging cycles"). This information will be shown only if the battery type is supporting this information

- new in version 1.21:
-- correction of issues with "dark mode" in iOS13

- new in version 1.20:
-- additionally to SCE8000, now display types SCE7000, SCE6100 and EW-EN100 are supported too
-- adjustments for iOS13

- new in version 1.09:
-- now the max. peak power parameter could be individually modified too (10W - 500W, with valid license key AND motor firmware 4.2.7 - 4.6.1 up to 550W)

- due to compatibility with the parallel development of eMaxMobileApp for other smartphone platforms there is no version 1.08:

- new in version 1.07:
-- compatibility with Shimano motor firmware 4.7.1

- new in version 1.06:
-- battery residual indication

- new in version 1.05:
-- correction of uncommon iPhone4 & iPhone5 problems with Shimano motor firmware 4.7.0 due to 32bit nature of Apple A4-A6 architecture
-- correction of indication of * 4.3.2 if * 4.7.0 was successfully read before without restarting the app
-- correction of "xxxxxx" destination indication when starting the app

- new in version 1.04:
-- correction of "XXXXXX" destination indication in "bike information view"

- new in version 1.03:
-- correction of missing destination setting in "bike information view"
-- "special settings" functions now are working successfully also without license key
-- correction of max. valid app version number in bike information view

- new in version 1.02:
-- correction of sporadically missing destination setting in "bike information view" with motor firmware 4.2.7-4.3.2
-- "special settings" now already accessible without license key
-- typo fixing

- new in version 1.01:
-- compatibility with Shimano motor firmware 4.7.0
-- bilingual interface English/German
-- list for 10 additional licence keys
-- extended warnings and messages
-- fixing of minor bugs
-- possibility to change gear type (mechanical to electronical Di2 and vice versa) after fitting bike accordingly
-- possibility to modify remaining light time (to get more mileage out of battery)

This version 1.21 for STEPS8xxx drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
All "motor performance settings" and "special settings" (change of gear type, change of remaining light time) could be used in the license free version.
For increasing motor max. support speed an additional license key is necessary. See also www.eMax-Tuning.com.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

- new in version 1.21:
-- correction of issues with "dark mode" in iOS13

- new in version 1.20:
-- additionally to SCE8000, now display types SCE7000, SCE6100 and EW-EN100 are supported too
-- adjustments for iOS13

- new in version 1.09:
-- now the max. peak power parameter could be individually modified too (10W - 500W, with valid license key AND motor firmware 4.2.7 - 4.6.1 up to 550W)

- due to compatibility with the parallel development of eMaxMobileApp for other smartphone platforms there is no version 1.08:

- new in version 1.07:
-- compatibility with Shimano motor firmware 4.7.1

- new in version 1.06:
-- battery residual indication

- new in version 1.05:
-- correction of uncommon iPhone4 & iPhone5 problems with Shimano motor firmware 4.7.0 due to 32bit nature of Apple A4-A6 architecture
-- correction of indication of * 4.3.2 if * 4.7.0 was successfully read before without restarting the app
-- correction of "xxxxxx" destination indication when starting the app

- new in version 1.04:
-- correction of "XXXXXX" destination indication in "bike information view"

- new in version 1.03:
-- correction of missing destination setting in "bike information view"
-- "special settings" functions now are working successfully also without license key
-- correction of max. valid app version number in bike information view

- new in version 1.02:
-- correction of sporadically missing destination setting in "bike information view" with motor firmware 4.2.7-4.3.2
-- "special settings" now already accessible without license key
-- typo fixing

- new in version 1.01:
-- compatibility with Shimano motor firmware 4.7.0
-- bilingual interface English/German
-- list for 10 additional licence keys
-- extended warnings and messages
-- fixing of minor bugs
-- possibility to change gear type (mechanical to electronical Di2 and vice versa) after fitting bike accordingly
-- possibility to modify remaining light time (to get more mileage out of battery)

This version 1.20 for STEPS8xxx drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
All "motor performance settings" and "special settings" (change of gear type, change of remaining light time) could be used in the license free version.
For increasing motor max. support speed an additional license key is necessary. See also www.eMax-Tuning.com.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

- new in version 1.20:
-- additionally to SCE8000, now display types SCE7000, SCE6100 and EW-EN100 are supported too
-- adjustments for iOS13

- new in version 1.09:
-- now the max. peak power parameter could be individually modified too (10W - 500W, with valid license key AND motor firmware 4.2.7 - 4.6.1 up to 550W)

- due to compatibility with the parallel development of eMaxMobileApp for other smartphone platforms there is no version 1.08:

- new in version 1.07:
-- compatibility with Shimano motor firmware 4.7.1

- new in version 1.06:
-- battery residual indication

- new in version 1.05:
-- correction of uncommon iPhone4 & iPhone5 problems with Shimano motor firmware 4.7.0 due to 32bit nature of Apple A4-A6 architecture
-- correction of indication of * 4.3.2 if * 4.7.0 was successfully read before without restarting the app
-- correction of "xxxxxx" destination indication when starting the app

- new in version 1.04:
-- correction of "XXXXXX" destination indication in "bike information view"

- new in version 1.03:
-- correction of missing destination setting in "bike information view"
-- "special settings" functions now are working successfully also without license key
-- correction of max. valid app version number in bike information view

- new in version 1.02:
-- correction of sporadically missing destination setting in "bike information view" with motor firmware 4.2.7-4.3.2
-- "special settings" now already accessible without license key
-- typo fixing

- new in version 1.01:
-- compatibility with Shimano motor firmware 4.7.0
-- bilingual interface English/German
-- list for 10 additional licence keys
-- extended warnings and messages
-- fixing of minor bugs
-- possibility to change gear type (mechanical to electronical Di2 and vice versa) after fitting bike accordingly
-- possibility to modify remaining light time (to get more mileage out of battery)

This version 1.09 is capable to communicate with the SCE8000 display.
We try to implement the communication to SCE7000, SCE6100 and EW-EN100 in one of the next versions.
All "motor performance settings" and "special settings" (change of gear type, change of remaining light time) could be used in the license free version.
For increasing motor max. support speed an additional license key is necessary. See also www.eMax-Tuning.com.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

- new in version 1.09:
-- now the max. peak power parameter could be individually modified too (10W - 500W, with valid license key AND motor firmware 4.2.7 - 4.6.1 up to 550W)

- due to compatibility with the parallel development of eMaxMobileApp for other smartphone platforms there is no version 1.08:

- new in version 1.07:
-- compatibility with Shimano motor firmware 4.7.1

- new in version 1.06:
-- battery residual indication

- new in version 1.05:
-- correction of uncommon iPhone4 & iPhone5 problems with Shimano motor firmware 4.7.0 due to 32bit nature of Apple A4-A6 architecture
-- correction of indication of * 4.3.2 if * 4.7.0 was successfully read before without restarting the app
-- correction of "xxxxxx" destination indication when starting the app

- new in version 1.04:
-- correction of "XXXXXX" destination indication in "bike information view"

- new in version 1.03:
-- correction of missing destination setting in "bike information view"
-- "special settings" functions now are working successfully also without license key
-- correction of max. valid app version number in bike information view

- new in version 1.02:
-- correction of sporadically missing destination setting in "bike information view" with motor firmware 4.2.7-4.3.2
-- "special settings" now already accessible without license key
-- typo fixing

- new in version 1.01:
-- compatibility with Shimano motor firmware 4.7.0
-- bilingual interface English/German
-- list for 10 additional licence keys
-- extended warnings and messages
-- fixing of minor bugs
-- possibility to change gear type (mechanical to electronical Di2 and vice versa) after fitting bike accordingly
-- possibility to modify remaining light time (to get more mileage out of battery)

This version 1.07 is capable only to communicate with the SCE8000 display.
We try to implement the communication to SCE7000, SCE6100 and EW-EN100 in the next version.
All "motor performance settings" and "special settings" (change of gear type, change of remaining light time) could be used in the license free version.
For increasing motor max. support speed an additional license key is necessary. See also www.eMax-Tuning.com.
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

- new in version 1.07:
-- compatibility with Shimano motor firmware 4.7.1

- new in version 1.06:
-- battery residual indication

- new in version 1.05:
-- correction of uncommon iPhone4 & iPhone5 problems with Shimano motor firmware 4.7.0 due to 32bit nature of Apple A4-A6 architecture
-- correction of indication of * 4.3.2 if * 4.7.0 was successfully read before without restarting the app
-- correction of "xxxxxx" destination indication when starting the app

- new in version 1.04:
-- correction of "XXXXXX" destination indication in "bike information view"

- new in version 1.03:
-- correction of missing destination setting in "bike information view"
-- "special settings" functions now are working successfully also without license key
-- correction of max. valid app version number in bike information view

- new in version 1.02:
-- correction of sporadically missing destination setting in "bike information view" with motor firmware 4.2.7-4.3.2
-- "special settings" now already accessible without license key
-- typo fixing

- new in version 1.01:
-- compatibility with Shimano motor firmware 4.7.0
-- bilingual interface English/German
-- list for 10 additional licence keys
-- extended warnings and messages
-- fixing of minor bugs
-- possibility to change gear type (mechanical to electronical Di2 and vice versa) after fitting bike accordingly
-- possibility to modify remaining light time (to get more mileage out of battery)

This version 1.06 is capable only to communicate with the SCE8000 display.
We try to implement the communication to SCE7000, SCE6100 and EW-EN100 in the next version.
All "motor performance settings" and "special settings" (change of gear type, change of remaining light time) could be used in the license free version.
For increasing motor max. support speed an additional license key is necessary. See also www.eMax-Tuning.com.
With motor firmware 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

- new in version 1.06:
-- battery residual indication

- new in version 1.05:
-- correction of uncommon iPhone4 & iPhone5 problems with Shimano motor firmware 4.7.0 due to 32bit nature of Apple A4-A6 architecture
-- correction of indication of * 4.3.2 if * 4.7.0 was successfully read before without restarting the app
-- correction of "xxxxxx" destination indication when starting the app

- new in version 1.04:
-- correction of "XXXXXX" destination indication in "bike information view"

- new in version 1.03:
-- correction of missing destination setting in "bike information view"
-- "special settings" functions now are working successfully also without license key
-- correction of max. valid app version number in bike information view

- new in version 1.02:
-- correction of sporadically missing destination setting in "bike information view" with motor firmware 4.2.7-4.3.2
-- "special settings" now already accessible without license key
-- typo fixing

- new in version 1.01:
-- compatibility with Shimano motor firmware 4.7.0
-- bilingual interface English/German
-- list for 10 additional licence keys
-- extended warnings and messages
-- fixing of minor bugs
-- possibility to change gear type (mechanical to electronical Di2 and vice versa) after fitting bike accordingly
-- possibility to modify remaining light time (to get more mileage out of battery)

This version 1.05 is capable only to communicate with the SCE8000 display.
We try to implement the communication to SCE7000, SCE6100 and EW-EN100 in the next version.
All "motor performance settings" and "special settings" (change of gear type, change of remaining light time) could be used in the license free version.
For increasing motor max. support speed an additional license key is necessary. See also www.eMax-Tuning.com.
With motor firmware 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)

- new in version 1.05:
-- correction of uncommon iPhone4 & iPhone5 problems with Shimano motor firmware 4.7.0 due to 32bit nature of Apple A4-A6 architecture
-- correction of indication of * 4.3.2 if * 4.7.0 was successfully read before without restarting the app
-- correction of "xxxxxx" destination indication when starting the app

- new in version 1.04:
-- correction of "XXXXXX" destination indication in "bike information view"

- new in version 1.03:
-- correction of missing destination setting in "bike information view"
-- "special settings" functions now are working successfully also without license key
-- correction of max. valid app version number in bike information view

- new in version 1.02:
-- correction of sporadically missing destination setting in "bike information view" with motor firmware 4.2.7-4.3.2
-- "special settings" now already accessible without license key
-- typo fixing

- new in version 1.01:
-- compatibility with Shimano motor firmware 4.7.0
-- bilingual interface English/German
-- list for 10 additional licence keys
-- extended warnings and messages
-- fixing of minor bugs
-- possibility to change gear type (mechanical to electronical Di2 and vice versa) after fitting bike accordingly
-- possibility to modify remaining light time (to get more mileage out of battery)

Take care:
This version 1.03 is capable only to communicate with the SCE8000 display. We try to implement the communication to SCE7000, SCE6100 and EW-EN100 in the next version.

With motor firmware 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.

- new in version 1.03:
-- correction of missing destination setting in "bike information view"
-- "special settings" functions now are working successfully also without license key
-- correction of max. valid app version number in bike information view

- new in version 1.02:
-- correction of sporadically missing destination setting in "bike information view" with motor firmware 4.2.7-4.3.2
-- "special settings" now already accessible without license key
-- typo fixing

- new in version 1.01:
-- compatibility with Shimano motor firmware 4.7.0
-- bilangual interface English/German
-- list for 10 additional licence keys
-- extended warnings and messages
-- fixing of minor bugs
-- possibility to change gear type (mechanical to electronical Di2 and vice versa) after fitting bike accordingly
-- possibility to modify remaining light time (to get more mileage out of battery)

- improvements since 1.00:
- compatibility with Shimano motor firmware 4.7.0
- bilangual interface English/German
- list for 10 additional licence keys
- extended warnings and messages
- fixing of minor bugs
- possibility to change gear type (mechanical to electronical Di2 and vice versa) after fitting bike accordingly
- possibility to modify remaining light time (to get more mileage out of battery)

- improvements since 1.01:
-- correction of sporadically missing destination setting in "bike information view" with firmer 4.2.7-4.3.2
-- "special settings" now already accessible without license key
-- typo


Take care:
This version 1.01 is capable only to communicate with the SCE8000 display. We try to implement the communication to SCE7000, SCE6100 and EW-EN100 in the next version.

With motor firmware 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.

- compatibility with shimano motor firmware 4.7.0
- bilangual interface English/German
- list for 10 additional licence keys
- extended warnings and messages
- fixing of minor bugs
- possibility to change gear type (mechanical to electronical Di2 and vice versa) after fitting bike accordingly
- possibility to modify remaining light time (to get more mileage out of battery)

Take care:
This version 1.01 is capable only to communicate with the SCE8000 display. We try to implement the communication to SCE7000, SCE6100 and EW-EN100 in the next version.

With motor firmware 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.