WifiRtt
P2P transfer rate
Gratuit
2.2for iPhone, iPad and more
Age Rating
WifiRtt Captures d'écran
About WifiRtt
Measure performance (Bandwidth between 2 devices.) on two Apple devices within the same subnet.(iPhone/iPad/iMac)
For example
・Near the WIFI router,but performance is no good..
・check wifi performance & reliability.
Please use app for problem analizing such.
usage)
One is a measurement terminal.
The other is Partner, it is a response terminal.
select Measure / Partner at first time.
(Partner)
This is response device side, the standby state is immediately entered.
There is the two-dimensional code with of the IP and port number of this terminal in screen center.
This code is used cominucation infomation by the measure devie.
Below that code, current using IP is displayed.
If you have multiple IPs, you can change them with the IP button.
(Measure)
This is measuring device side,
we must set Paertner device IP and this device IP.
Paertner device IP is readed the 2D code of the partner device with the camera.
The current using IP of your own is displayed under the partner device IP.
If you have multiple IPs, you can change them with the IP button.
The measurement results differ depending on the type of device.
Especially, the difference on the measurement side is remarkable. This depends on the TCP / IP processing performance (congestion and processing performance) of the device.
You can remeasuring with the update button on measuring screen.
Press and hold this button (about 3 seconds) to switch between continuous measurement mode and single measurement mode.
For example
・Near the WIFI router,but performance is no good..
・check wifi performance & reliability.
Please use app for problem analizing such.
usage)
One is a measurement terminal.
The other is Partner, it is a response terminal.
select Measure / Partner at first time.
(Partner)
This is response device side, the standby state is immediately entered.
There is the two-dimensional code with of the IP and port number of this terminal in screen center.
This code is used cominucation infomation by the measure devie.
Below that code, current using IP is displayed.
If you have multiple IPs, you can change them with the IP button.
(Measure)
This is measuring device side,
we must set Paertner device IP and this device IP.
Paertner device IP is readed the 2D code of the partner device with the camera.
The current using IP of your own is displayed under the partner device IP.
If you have multiple IPs, you can change them with the IP button.
The measurement results differ depending on the type of device.
Especially, the difference on the measurement side is remarkable. This depends on the TCP / IP processing performance (congestion and processing performance) of the device.
You can remeasuring with the update button on measuring screen.
Press and hold this button (about 3 seconds) to switch between continuous measurement mode and single measurement mode.
Show More
Quoi de neuf dans la dernière version 2.2
Last updated on Nov 19, 2021
Vieilles Versions
Ver2.2
bugFix
.Frequent pairing failures
bugFix
.Frequent pairing failures
Show More
Version History
2.2
Nov 19, 2021
Ver2.2
bugFix
.Frequent pairing failures
bugFix
.Frequent pairing failures
2.1
Nov 14, 2021
Ver2.1
bugFix
.The port value in the configuration may not be set.
.Configuration timeout may not be set
function
.Addition of operation description
bugFix
.The port value in the configuration may not be set.
.Configuration timeout may not be set
function
.Addition of operation description
2.0
Nov 10, 2021
Conventional function was round trip time measurement by UDP.
We changed this function to the transfer speed between two devices. Because we realized that bandwidth measurement is more important than the traditional function.
It also supports IPV6 and wired LAN, so please analyze network problems.
Two iOS devices are required for measurement.
We changed this function to the transfer speed between two devices. Because we realized that bandwidth measurement is more important than the traditional function.
It also supports IPV6 and wired LAN, so please analyze network problems.
Two iOS devices are required for measurement.
1.3
Feb 18, 2021
fix ios14
change Admob framework
change Admob framework
1.2
Aug 14, 2020
fix for ios13sdk
check WIFI switch
check WIFI switch
1.1
Jan 22, 2018
fixed some issue
1. ssid reload for the select screen.
2.display version for the select screen.
3.add sampling time setting(default 1s)
1. ssid reload for the select screen.
2.display version for the select screen.
3.add sampling time setting(default 1s)
1.0
Dec 9, 2016
WifiRtt FAQ
Cliquez ici pour savoir comment télécharger WifiRtt dans un pays ou une région restreints.
Consultez la liste suivante pour voir les exigences minimales de WifiRtt.
iPhone
Nécessite iOS 9.0 ou version ultérieure.
iPad
Nécessite iPadOS 9.0 ou version ultérieure.
Mac
Nécessite macOS 10.15 ou version ultérieure.
iPod touch
Nécessite iOS 9.0 ou version ultérieure.
WifiRtt prend en charge Anglais