VictronConnect

- Fix battery monitors first use setup

- Add BMV-712 and SmartShunt Bluetooth firmware v2.46

- Add VE.Bus Smart Dongle firmware v1.17
- Fix .bup firmware updates on iOS 17
- Fix some MPPT the settings save/load buttons
- Add new Multi models
- Make system configuration available in Inverter/Multi RS demo products

- Add Inverter RS firmware v1.12: Add support for AC output parallel and 3-phase operation.
- Add Multi RS firmware v1.12
- Add VE.Bus Smart Dongle firmware v1.14
- Add a feature to lock VictronConnect on to a demo product. Useful for exhibitions and training.
- Various small fixes

- Include firmware v470 for MultiPlus-II
- Fix issues when pressing continue button after a firmware update is completed

* Performance improvements
* Fix notifications drawer don't update the alarm/warning/error description is some cases
* Order demo groups alphabetically

SmartSolar VE.Can:
* Fix firmware updating via Bluetooth

GX devices:
* Improve Venus network settings layout
* Add new icons for Cerbo GX, Maxi GX, Octo GX and MultiPlus-II GX

Solar Chargers:
* Change default CSV name to SolarCharger instead of BlueSolar

Smart Chargers:
* Add default value to re-bulk current setting to the demo of those models that support advanced settings

Smart Battery Protect:
* Fix load output switch stays at off position when it should be in on position after pressing cancel in the deactivation warning dialog

BMV:
* Fix Input section is overlapped on BMV demos

SmartShunt:
* Add SmartShunt demo products

SmartLithium:
* Add 12V 100&150 Ah models

* General performance improvements
* Do not show default PIN code warning when there is a mandatory update available
* Fix missing decimal digits and units for trends
* Show a warning when trying to use an invalid firmware file

GX devices:
* Auto select the correct host for the remote console when connected via Bluetooth

Solar Chargers:
* Improve StreetLight settings UX
* Improve TX port and Load output settings UX
* Add support for new models

Blue Smart Chargers:
* Do not show advanced settings on demos when not supported by the charger

Phoenix Inverter:
* Set 60Hz as default freq. for 120V Phoenix Inverter demos

BMV-720
* Optimise the firmware file format to improve the update speed
* No changes related, version is kept as v4.03.

Smart Chargers:
* Add re-bulk current setting

VE.Bus Inverter/Chargers:
* Include latest firmware, v469
* Add missing name/model description for some MultiPlus models

- Fix GX devices discovery

- Fix firmware version is not shown in all the cases when the update is completed
- Fix “update succeeded” message is wrongly displayed when trying to update using an invalid file
- Various user interface fixes and improvements

VE.Smart network:
- Change the way that a VE.Smart network information is presented:
- Show devices that are in range for the connected product
- Devices in range signal strength

Smart Battery Sense:
- Add firmware update v1.05

Bluetooth internal and external dongles:
- Add Bluetooth firmware v2.23

MPPT SolarChargers:
- Add MPPT Solar Chargers firmware v1.46:
- Update marked mandatory only for SmartSolar as these models are affected by the bug described below.
- Fix bug on the internal temperature measurement that lead to not being able to de-rate the output current due to a high temperature nor triggering the over temperature protection. (Bug introduced on v1.30). This bug is only present in SmartSolar.
- Make 30 day history in demos more accurate

BMV-712:
- Add BMV-712 firmware v4.03:
- Fix an issue that makes the buzzer inaudible

VE.Bus Inverter/Chargers:
- Add firmware version 465 & 466(MultiPlus-II) update
- Charger settings:
- Add battery temperature compensation setting
- Fix “Lithium battery” switch state doesn't reflect the actual value of the setting
- Change hysteresis for Low DC Disconnect and Restart setting
- Fix crash when an invalid firmware update file is selected
- Add errors notification


Smart Battery Protect:
- Show the correct icon for Smart Battery Protect 48-100

SmartLithium:
- Add firmware version 1.17 update:
- Add cell under voltage pre-alarm threshold setting
- Add support for BMS Pre-Alarm

- Fix firmware version is not shown in all the cases when the update is completed
- Fix “update succeeded” message is wrongly displayed when trying to update using an invalid file
- Various user interface fixes and improvements

VE.Smart network:
- Change the way that a VE.Smart network information is presented:
- Show devices that are in range for the connected product
- Devices in range signal strength

Smart Battery Sense:
- Add firmware update v1.05

Bluetooth internal and external dongles:
- Add Bluetooth firmware v2.23

MPPT SolarChargers:
- Add MPPT Solar Chargers firmware v1.46:
- Update marked mandatory only for SmartSolar as these models are affected by the bug described below.
- Fix bug on the internal temperature measurement that lead to not being able to de-rate the output current due to a high temperature nor triggering the over temperature protection. (Bug introduced on v1.30). This bug is only present in SmartSolar.
- Make 30 day history in demos more accurate

BMV-712:
- Add BMV-712 firmware v4.03:
- Fix an issue that makes the buzzer inaudible

VE.Bus Inverter/Chargers:
- Add firmware version 465 update
- Charger settings:
- Add battery temperature compensation setting
- Fix “Lithium battery” switch state doesn't reflect the actual value of the setting
- Change hysteresis for Low DC Disconnect and Restart setting
- Fix crash when an invalid firmware update file is selected
- Add errors notification


Smart Battery Protect:
- Show the correct icon for Smart Battery Protect 48-100

SmartLithium:
- Add firmware version 1.17 update:
- Add cell under voltage pre-alarm threshold setting
- Add support for BMS Pre-Alarm

Fix VictronConnect could not recover properly after an interrupted Bluetooth update of the Bluetooth microcontroller

General:
- Firmware updates are no longer mandatory for basic monitoring:
- Live data page: This page can be accessed without updating the firmware unless the update is highly recommended and marked as mandatory.
- Setting pages: To view and modify settings it is always necessary to update the product to the latest version included in VictronConnect.

- Show a warning when using Default PIN via BLE
- Default PIN code must be always changed to prevent unwanted connections, now we advise it when default PIN code has not been changed

- Trends tab remembers last selected graphs for certain product family
- Improve PIN code change process
- Improve information shown when unable to connect to a product
- Fix PIN code reset via PUK code interface issues
- Fix settings files buttons could not appear when VE.Direct connected
- Do not allow change PIN code to same code
- Update the framework on top of which VictronConnect is built, required to comply with Google Play Store requirements. This will improve the application performance but adds a drawback: We have to drop support for old OS versions, see below.

MPPT Chargers:

- Include firmware v1.42 (v1.43 for some models) for BlueSolar and SmartSolar chargers:
-The Lithium battery rotary switch preset has been changed. Absorption time is fixed to 2 hours, and it will not stop on low tail current.
-The re-bulk voltage was lowered from 13.7V to 13.4V (for all battery types).
-Added four new settings:
-Adjustable tail current (changeover from absorption to float).
-Adjustable re-bulk offset voltage (changeover from float to bulk).
-Adjustable automatic equalization parameters (current / duration).
-Choose between adaptive- and fixed- absorption time. Note that we advise to not use fixed absorption times for lead batteries.

- Include firmware v1.02 for SmartSolar VE.Can:
- Synchronized charging with VE.Can. This works the same as with previous models and the Skylla-i.
- Add ESS support.
- Add BMS support.
- All new battery charger settings: fixed absorption, tail current, re-bulk offset voltage, max auto equalization time, equalization auto stop and equalization current percentage
- Support for the Smart Battery Sense and BMV connected via Bluetooth VE.Smart.

SmartShunt:
- Add support for new SmartShunt product

BMV:
- Fix empty item in the transmitting list is shown in the VE.Smart networking settings page.

Orion Smart:
- Add firmware v1.02
- Add engine shutdown detection setting
- Fix adaptive mode is not changed when selecting a battery preset

BlueSmart Chargers IP65:
- Enable PUK code PIN reset when the product supports it

VE.Direct Phoenix Inverter:
- Add firmware v1.17
- Add "ECO search time" setting
- Add option to disable Bluetooth on Smart models

VE.Bus Inverter/Chargers:
- Add latest firmware versions (460 & 463)
- VeBusInverter: Reduce minimum DC Input low restart voltage (24V/48V)
- The minimum DC Low Restart has been lowered for 24V models from 21.8 to 20.6, and from 43.6 to 41.2 for 48V models. Not for 12V units, due to hardware limitations.

IMPULSE-II chargers:
- Add charge cycles history

- Add support for Orion Smart
- Performance improvements
- Add instructional videos of how to remove the device pairing, required after a PIN code change

Inverter/Chargers over VE.Bus MK3-USB interface:
- Add settings and firmware updates
- Latest firmware versions are included in the app and auto selected when updating.
- Basic settings are included, Virtual Switch and Assistants are not supported
- Only single unit systems are supported

VE.Can MPPT:
- Include firmware v1.02
- Synchronized charging with VE.Can. This works the same as with previous models.
- Add ESS support.
- Add BMS support.

SmartSolar chargers, Smart BMV, Smart Phoenix Inverters & VE.Direct Smart Bluetooth dongle, Include firmware v2.19:
- Fix for using wrong BLE advertisement
- Fix for higher current consumption for Phoenix Inverter Smart in “Off” state.

Smart Battery Sense:
- Include firmware v1.04 update

Blue Smart Chargers:

- Update the link pointing to the manual shown when a firmware update fails

MPPT Solar Chargers:
- Demo products: Scale settings accordingly the battery voltage

- Fix PIN code change button is not shown

MPPT Solar Chargers:
- Prepare support for future firmware versions

- Fix firmware update retry is not triggered when reconnecting after an unsuccessful firmware upadte.
- Internal improvements
- Fix disable Bluetooth toggle is shown twice for some products
- Make trends use user selected temperature unit
- Fix typos in Dutch and German translations

GX devices:
- Show firmware version when the GX device is running firmware >= 2.30

- Add support for Phoenix Smart Chargers.
- Add a setting to show temperature units in Fahrenheit.
- Add trend graphics for BMV, MPPT and Smart Battery Sense.
- Add onboarding, shows to the user a brief description of the available options.
- Add new features highlight on home screen.
- Add new features highlight on home screen.
- Improve reset pin code by PUK handling.
- Fix GX log converter day light saving issues.
- Fix EasySolar2 GX, Multiplus2 GX and Generic Venus devices are shown as Unknown devices when discovered over UPnP.

Smart Lithium Batteries:
- Add firmware v1.16 update:
Fix temperature inaccuracies. After updating to this version you can wait for the automatic calibration to take place or go in and set the temperature offset immediately. When doing so; the automatic calibration will not take place.

Add Venus device discovery via UPnP:
- List and connect to all the Venus devices available on a local network, now the remote console and VRM portal access are just one click away.
- Easily set up your Venus GX; Connect to its built-in Wi-Fi access point and use VictronConnect to open the remote console and configure the device.

- Fix English language is not selectable
- Improve Spanish translation

BMV Battery monitor:
- Fix "Battery starts synchronized" setting

Peak Power Pack:
- Fix wrong status is shown
- Add missing alarms
- Fix "0V" is displayed in case of an over voltage.

Smart Phoenix Inverter:
* Show the correct product icon for 1600/2000VA models

MPPT Solar Chargers:
- Include firmware v1.39 update:
- Reset-to-defaults: maintains battery voltage (12..48V) as long as the unit remains powered. Automatic voltage detection takes place on next power-cycle.

- Fix page device page is not closed after reconnection timeout

New products support:
- Smart Battery Protect
- Smart Phoenix Inverter

BMV Battery Monitor:
- BMV 712 Bluetooth firmware update v2.14

- BMV Battery monitor firmware v3.10(BMV 70x) and v4.01(Smart BMV) update
- Add “Battery starts synchronized” setting

VE.Direct Bluetooth Smart Dongle:
- Firmware v2.15 update:
- Increased VE.Smart transmission robustness.
- Start advertising after 20 seconds when no successful VE.Direct communication was possible

MPPT Solar Chargers:
- Add scrollbar to presets list
- Fix history totals text overlap
- SmartSolar Bluetooth firmware v2.14 update:
- Increased VE.Smart transmission robustness.
- Start advertising after 20 seconds when no successful VE.Direct communication was possible.

Smart Battery Sense:
- Add firmware v1.03 update
- Improve Bluetooth range

VE.Bus Inverter/Charger:
- Fix overload alarm icon is missing

* Fix products on the devices list page are displayed with the default name instead of the custom name.

SmartLithium
* Include firmware v1.15 update
* Add "Allowed-To-Charge minimum temperature" setting
* By default it disables charge when battery temperature is below 5C.
* Fix SmartLithium disappears from de devices list after disconnecting.

BMV Battery monitor:
* Fix an issue that makes BMV disappear from devices list after disconnecting. This issue only affects to BMV which are configured for VE.Smart networking.

MPPT solar chargers:
* Fix AES time show undefined in the algorithm description

Phoenix Inverter:
* Fix AC output setting limits in demo products

MPPT solar chargers:
- Added firmware v1.37 update

BMV battery monitor:
- Fix time remaining displays “0m” when no current is flowing from or to the battery

- Fix issue that can cause VictronConnect get stuck at 93% during a VE.Direct product firmware update

VE.Bus Smart Bluetooth Dongle
- Added firmware v1.07 update
- Fixed an issue that makes the page show no values in some situations
- Hide SOC items when battery monitor is disabled
- Added missing Multi's model names
- Fix issues when connected Multi/Quattro firmware version is lower than 415.
- Warn about minimum firmware version

MPPT solar chargers:
- Added firmware v1.36 update for 250V models
- Load output: User algorithm 1&2 minimum voltage is now 10V for 12V systems.

BMV battery monitor:
- Added power value reading to the main page
- Fix time to go reported as “Infinite” instead of “0h” when discharge floor SOC level is reached
- Fix high voltage relay setting reports wrong values when editting for a first time in the session

Blue Smart Charger:
- Show correct values for low current setting in demo products

- Add support for VE.Bus Smart Dongle
- Add SmartLithium 24V 200Ah demo
- Fix device filtering needs to be set after each scan

- Fix products settings page is empty after automatic reconnection.

IP65 Blue Smart Charger:
- Fix test stage not being shown for Blue Smart IP65 chargers

- Improve VE.Direct firmware update robustness

- Add firmware v1.33 update for 250V models
- Further improve PV Short protection.
- Fix in reporting current/wattage/state when the unit is not charging.

- Add Chinese translation

- Fix issue that makes settings files not being saved if no “.vcsf” extension is manually appended to the filename.

- Fix French translation for “Switch on before sunrise” in Streetlight settings

Solar Chargers:
- Add firmware v1.32 update for 250V models
- Improve power-stage shutdown sequence.
- Improve / speed-up PV Short protection and introduce error code 39
- Fix PV current value stops updating two minutes after connecting
- Fix oldest day record is not exported to CSV file

BMV battery monitor:
- Fix temperature alarm and relay settings are always reported as disabled when Fahrenheit unit is selected

Solar Chargers:
- Add VE.Smart Networking support
- Added firmware v1.30 update
- Added internal bluetooth firmware v2.12 update
- Add low temp cut-off setting, prevents damage in lithium batteries by disabling the charge during low temperature conditions.
- Show battery temperature when the MPPT is configured in a VE.Smart network where the battery temperature is available.
- Send local time to the MPPT to help streetlights functionality synchronization.
- Fix a bug that keeps streetlights on after sunrise.

BMV battery monitor:
- Added internal bluetooth firmware v2.12 update
- Added support for VE.Smart Networking
- Fix mid-point deviation unit, it was “V” when it should be “%”

SmartLithium:
- Added firmware v1.12 update
- Add “Allowed-To-Discharge cell voltage” setting
- Fix low cell voltage alarm

VE.Smart dongle:
- Added firmware v2.12 update (only for rev2 units)
- Added support for VE.Smart Networking

SmartBatterySense:
- Added firmware v1.02 update
- Added support for VE.Smart Networking (Voltage & Temp)

PeakPowerPack:
- Show confirmation dialog before switching to hibernate

- Fix duplicated error message when loading an invalid settings file.
- Allow restoring settings from files created with previous VictronConnect versions
- Add scroll bars to device list and settings pages
- Add mouseover effect to the refresh button in the device list page
- Rename "CCGX log converter" to "Venus log converter"


SmartLithium:
- Disable false low cell voltage alarm
- Rename battery to voltage in right panel

MPPT Solar chargers:
- Fix save/load settings functionality on BlueSolar 150/100 model
- Add relay state to live data page
- Add an error in one of the history records of the demo products
- Rename load output to virtual load output on devices without load output
- Add description to day/night detection settings
- History graphs:
- Hide Bluk, Absorption or Float segments when the state was not reached
- Improve bar length on days without production
- Add scrollbars
- Add mouseover to bars and buttons
- Fix daily records values are partially hidden on some small screens, for example iPhone 5 & iPhone SE
- Fix text overlapping due to translations

Phoenix Inverters:
- Fix save and load settings icons are disabled when using VE.Direct cable
- Add mode setting, mode now can be switched between on, off and ECO
- Add support for future models
- Add firmware v1.14 update for 800VA models

Blue Smart Chargers:
- Improve Bluk state description when Li-ion battery is selected

- Completely redesigned user interface:
- Context help for settings
- Improved user experience
- Smoother navigation
- Responsive layout

- Added translations: Dutch, French, German, Italian and Spanish.

SmartLithium:
- New firmware update v1.07

MPPT solar chargers:
- Improved history page with graphs
- Added user battery presets library
- Included firmware v1.29 update
- Show the actual state when performing an automatic equalisation

- Completely redesigned user interface:
- Context help for settings
- Improved user experience
- Smoother navigation
- Responsive layout

- Added translations: Dutch, French, German, Italian and Spanish.

SmartLithium:
- New firmware update v1.07

MPPT solar chargers:
- Improved history page with graphs
- Added user battery presets library
- Included firmware v1.29 update
- Show the actual state when performing an automatic equalisation

- Fix “Restore default settings” button, settings are not restored when pressed

BMV:
- Fix save/load settings buttons not displayed on BMV700

Phoenix inverters:
- Fix “Store settings” button, settings are not stored when pressed

Blue Smart Chargers:
- Fix low current mode toggled when opening app from background.
- Show the proper firmware error messages when the update fails.
- Improve firmware update error message including a link to Victron Live troubleshooting.
- Include firmware v3.0 update:
- Internal improvements
- For some models the update might take a little longer, as the the hardware shuts down and it takes a little while to recover from this (approx. 10-15 seconds).

Settings:
- Add support for the new SmartSolar 75/10, 75/15, 100/15, 100/20, 100/30, 100/50, 150/35 & 150/100.

Demos:
- Add SmartSolar 75/10, 75/15, 100/15, 100/20, 100/30, 100/50, 150/35 & 150/100 to the demo library.

- Settings files: Save, load and share product settings.

- Demo products. A demo product can be used to:
- Learn and show the options available for different products.
- Create a specific setup, save that and send it to a customer so they can put it in their device.
- Besides loading products from the standard library, it is also possible to load it from a saved file.

- Allow filtering of the device list
- Feedback when a setting is correctly stored in the device
- General interface improvements

BlueSolar & SmartSolar MPPT chargers:
- Include firmware v1.27 update
- Added a button to disable the charger
- Added StreetLight night and day detection delay setting
- Added inverted load on/off mode for Rx port function
- Remove automatic battery voltage detection option:
- Added a button to manually start Equalisation. (note this is not available for older models)

Add manual firmware updates for Bluetooth

SmartLithium batteries:
- Rename “Communication error” to “Internal communication failure”.
- Improve BMS state information display
- SmartLithium firmware v1.06 update:
- Fix a problem with internal communication

SmartSolar 250/85 & SmartSolar 250/100 firmware v1.25 update

Fix an issue that makes that in certain conditions the latest edited setting is not sent to the product when leaving the settings page.

MPPT Solar Chargers:
- Include firmware v1.24 update for Smart Solar 250/100 and 250/85
- Bug-fix in the battery voltage setting: the voltage always read as AUTO even if it is manually selected. Updating the MPPT 250/100 or 250/85 from v1.23 to v1.24 will change the voltage setting to 'AUTO', make sure to set the battery voltage to the correct voltage after updating.

Phoenix Inverters:
- Improve live data page
- Set minimum value for “ECO minimum wake-up power” setting to 15W.

- MPPT chargers firmware v1.23 update

- MPPT solar chargers firmware update
- Improve firmware update robustness

- Add support for 120V VE.Direct Phoenix Inverters
- Add support for future new products