Ardu-Con - Arduino Controller
$0.99
2.1for iPhone, iPod touch
Age Rating
Ardu-Con - Arduino Controller Screenshots
About Ardu-Con - Arduino Controller
Ardu-Con is an application that allows you to turn your iPhone into six channels remote control ( R/C ) to access up to 4 relays and 2 servos through your Arduino UNO connected to an Ethernet or Wifi Shield.
The Ardu-Con application perfectly emulates the switches commands and sticks as a true remote control and sends the data through web requests to your local network.
Your iPhone must be connected to the same network via WiFi.
There are no limits to the imagination and possibilities.
You can control robots, vehicles, lamps and many others devices.
Simply access the settings screen and configure the IP address that is connected to your Ethernet Shield, and connect the necessary hardware to be controlled (LEDs , relays, motors and servos).
Also in settings, you can configure the controller mode:
You can set it up to look like a single “Joystick”, a “Bubble Level Controller”, “T-like Sliders” or “Two Parallel Sliders”. In addition, you can configure the behavior of joystick (sliders), as well the bubble sensivity.
This facilitates the control of devices such as cars, helicopters, planes or drones.
Uploading the sketch to your arduino:
The "Source Code" for the Arduino is described in the application itself. It is written in a clear code and with comments to be freely modified and adapted to your needs.
Simply touch the code to select it, then copy to the clipboard and paste into the notepad , send via e-mail , etc. Transfer to the application that will program your Arduino board.
Read the INFO in the application to learn more about the transmission protocol details and how to connect the Arduino and components.
The Ardu-Con application perfectly emulates the switches commands and sticks as a true remote control and sends the data through web requests to your local network.
Your iPhone must be connected to the same network via WiFi.
There are no limits to the imagination and possibilities.
You can control robots, vehicles, lamps and many others devices.
Simply access the settings screen and configure the IP address that is connected to your Ethernet Shield, and connect the necessary hardware to be controlled (LEDs , relays, motors and servos).
Also in settings, you can configure the controller mode:
You can set it up to look like a single “Joystick”, a “Bubble Level Controller”, “T-like Sliders” or “Two Parallel Sliders”. In addition, you can configure the behavior of joystick (sliders), as well the bubble sensivity.
This facilitates the control of devices such as cars, helicopters, planes or drones.
Uploading the sketch to your arduino:
The "Source Code" for the Arduino is described in the application itself. It is written in a clear code and with comments to be freely modified and adapted to your needs.
Simply touch the code to select it, then copy to the clipboard and paste into the notepad , send via e-mail , etc. Transfer to the application that will program your Arduino board.
Read the INFO in the application to learn more about the transmission protocol details and how to connect the Arduino and components.
Show More
What's New in the Latest Version 2.1
Last updated on Jan 9, 2024
Old Versions
Compatibility with the latest version of iOS.
Show More
Version History
2.1
Jan 9, 2024
Compatibility with the latest version of iOS.
2.0
Jul 16, 2020
iOS 13 Compatibility;
Display for visualizing key information and servo position;
Settings are now separate for each controller mode;
Graphical improvements.
Display for visualizing key information and servo position;
Settings are now separate for each controller mode;
Graphical improvements.
1.2.1
Jan 8, 2016
Fixed an issue about http blocking.
Included time of 10ms between messages to prevent Arduino buffer overflow;
Included redundant forwarding of the last message (5 times) to ensure that data will not be lost by Arduino reading.
Thank you for feedback!
Included time of 10ms between messages to prevent Arduino buffer overflow;
Included redundant forwarding of the last message (5 times) to ensure that data will not be lost by Arduino reading.
Thank you for feedback!
1.2
Nov 24, 2015
****
Please do not update.
This version has a problem and does not work properly.
We are awaiting the approval of the version 1.2.1 to solve this issue.
We are sorry for the inconvenience
****
Included time of 10ms between messages to prevent Arduino buffer overflow;
Included redundant forwarding of the last message (5 times) to ensure that data will not be lost by Arduino reading.
Thank you for feedback!
Please do not update.
This version has a problem and does not work properly.
We are awaiting the approval of the version 1.2.1 to solve this issue.
We are sorry for the inconvenience
****
Included time of 10ms between messages to prevent Arduino buffer overflow;
Included redundant forwarding of the last message (5 times) to ensure that data will not be lost by Arduino reading.
Thank you for feedback!
1.1
Jun 25, 2015
More options on the configuration screen.
Now you can configure the bubble data sent. (Reverse the X and Y axes).
Thank you for feedback!
Now you can configure the bubble data sent. (Reverse the X and Y axes).
Thank you for feedback!
1.0
Jun 15, 2015
Ardu-Con - Arduino Controller FAQ
Click here to learn how to download Ardu-Con - Arduino Controller in restricted country or region.
Check the following list to see the minimum requirements of Ardu-Con - Arduino Controller.
iPhone
Requires iOS 12.0 or later.
iPod touch
Requires iOS 12.0 or later.
Ardu-Con - Arduino Controller supports English