eMaxMobileApp
$0.99
1.83for iPhone, iPad and more
Age Rating
eMaxMobileApp Screenshots
About eMaxMobileApp
...the most advanced optimizing tool for STePS systems.
All Bluetooth capable displays SC-EM800, SC-E8000, SC-E7000, SC-E6100, SW-EN600-L switch and EW-EN100 cockpit are supported!
Additionally to DU-E80X0 motors, now DU-EP801, DU-EP800, DU-EP600, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
Partially compatible also with the latest Shimano motor firmware versions!
See www.eMax-Tuning.com or get detailed & personal information via eMail from info@eMax-Tuning.com
All Bluetooth capable displays SC-EM800, SC-E8000, SC-E7000, SC-E6100, SW-EN600-L switch and EW-EN100 cockpit are supported!
Additionally to DU-E80X0 motors, now DU-EP801, DU-EP800, DU-EP600, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
Partially compatible also with the latest Shimano motor firmware versions!
See www.eMax-Tuning.com or get detailed & personal information via eMail from info@eMax-Tuning.com
Show More
What's New in the Latest Version 1.83
Last updated on Sep 9, 2024
Old Versions
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.83 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.83 (07.09.24):
- bug fix for crash on some very rare bike configurations at 73% of bike information reading
new in version 1.82 (31.08.24):
- optimizations and minor bug fixes for DU-EP800
new in version 1.77 (30.06.24):
- partial compatibility for EP801/EP motor firmware 4.3.0
new in version 1.76 (15.06.24):
- new battery types and RS default values for generation 2 added
new in version 1.75 (12.06.24):
- bugfix for DU-E8000 motor firmware 4.10.0
new in version 1.74 (20.05.24):
- partial compatibility for DUEP800 (DUEP800, DUEP800-CRG) FW 4.2.0
- partial compatibility for DUE80X0 (DUE8000, DUE8080) FW 4.10.0
- partial compatibility for DUE7000 FW 4.8.0
- partial compatibility for DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.8.0
- partial compatibility for DUE50X0 (DUE5000, DUE5080) FW 4.5.0
See also https://www.emax-tuning.com/eMax-possibilities.pdf
new in version 1.73 (15.04.24):
- partial compatibility for EP801/EP motor firmware 4.2.2
new in version 1.72 (26.03.24):
- partial compatibility for EP801/EP motor firmware 4.2.1
new in version 1.71 (09.02.24):
- partial compatibility for EP801/EP motor firmware 4.2.0
- minor optimizations
new in version 1.70 (23.10.23):
- minor bug fix
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.83 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.83 (07.09.24):
- bug fix for crash on some very rare bike configurations at 73% of bike information reading
new in version 1.82 (31.08.24):
- optimizations and minor bug fixes for DU-EP800
new in version 1.77 (30.06.24):
- partial compatibility for EP801/EP motor firmware 4.3.0
new in version 1.76 (15.06.24):
- new battery types and RS default values for generation 2 added
new in version 1.75 (12.06.24):
- bugfix for DU-E8000 motor firmware 4.10.0
new in version 1.74 (20.05.24):
- partial compatibility for DUEP800 (DUEP800, DUEP800-CRG) FW 4.2.0
- partial compatibility for DUE80X0 (DUE8000, DUE8080) FW 4.10.0
- partial compatibility for DUE7000 FW 4.8.0
- partial compatibility for DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.8.0
- partial compatibility for DUE50X0 (DUE5000, DUE5080) FW 4.5.0
See also https://www.emax-tuning.com/eMax-possibilities.pdf
new in version 1.73 (15.04.24):
- partial compatibility for EP801/EP motor firmware 4.2.2
new in version 1.72 (26.03.24):
- partial compatibility for EP801/EP motor firmware 4.2.1
new in version 1.71 (09.02.24):
- partial compatibility for EP801/EP motor firmware 4.2.0
- minor optimizations
new in version 1.70 (23.10.23):
- minor bug fix
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
Show More
Version History
1.83
Sep 9, 2024
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.83 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.83 (07.09.24):
- bug fix for crash on some very rare bike configurations at 73% of bike information reading
new in version 1.82 (31.08.24):
- optimizations and minor bug fixes for DU-EP800
new in version 1.77 (30.06.24):
- partial compatibility for EP801/EP motor firmware 4.3.0
new in version 1.76 (15.06.24):
- new battery types and RS default values for generation 2 added
new in version 1.75 (12.06.24):
- bugfix for DU-E8000 motor firmware 4.10.0
new in version 1.74 (20.05.24):
- partial compatibility for DUEP800 (DUEP800, DUEP800-CRG) FW 4.2.0
- partial compatibility for DUE80X0 (DUE8000, DUE8080) FW 4.10.0
- partial compatibility for DUE7000 FW 4.8.0
- partial compatibility for DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.8.0
- partial compatibility for DUE50X0 (DUE5000, DUE5080) FW 4.5.0
See also https://www.emax-tuning.com/eMax-possibilities.pdf
new in version 1.73 (15.04.24):
- partial compatibility for EP801/EP motor firmware 4.2.2
new in version 1.72 (26.03.24):
- partial compatibility for EP801/EP motor firmware 4.2.1
new in version 1.71 (09.02.24):
- partial compatibility for EP801/EP motor firmware 4.2.0
- minor optimizations
new in version 1.70 (23.10.23):
- minor bug fix
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.83 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.83 (07.09.24):
- bug fix for crash on some very rare bike configurations at 73% of bike information reading
new in version 1.82 (31.08.24):
- optimizations and minor bug fixes for DU-EP800
new in version 1.77 (30.06.24):
- partial compatibility for EP801/EP motor firmware 4.3.0
new in version 1.76 (15.06.24):
- new battery types and RS default values for generation 2 added
new in version 1.75 (12.06.24):
- bugfix for DU-E8000 motor firmware 4.10.0
new in version 1.74 (20.05.24):
- partial compatibility for DUEP800 (DUEP800, DUEP800-CRG) FW 4.2.0
- partial compatibility for DUE80X0 (DUE8000, DUE8080) FW 4.10.0
- partial compatibility for DUE7000 FW 4.8.0
- partial compatibility for DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.8.0
- partial compatibility for DUE50X0 (DUE5000, DUE5080) FW 4.5.0
See also https://www.emax-tuning.com/eMax-possibilities.pdf
new in version 1.73 (15.04.24):
- partial compatibility for EP801/EP motor firmware 4.2.2
new in version 1.72 (26.03.24):
- partial compatibility for EP801/EP motor firmware 4.2.1
new in version 1.71 (09.02.24):
- partial compatibility for EP801/EP motor firmware 4.2.0
- minor optimizations
new in version 1.70 (23.10.23):
- minor bug fix
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
1.82
Sep 1, 2024
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.82 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.82 (31.08.24):
- optimizations and minor bug fixes for DU-EP800
new in version 1.77 (30.06.24):
- partial compatibility for EP801/EP motor firmware 4.3.0
new in version 1.76 (15.06.24):
- new battery types and RS default values for generation 2 added
new in version 1.75 (12.06.24):
- bugfix for DU-E8000 motor firmware 4.10.0
new in version 1.74 (20.05.24):
- partial compatibility for DUEP800 (DUEP800, DUEP800-CRG) FW 4.2.0
- partial compatibility for DUE80X0 (DUE8000, DUE8080) FW 4.10.0
- partial compatibility for DUE7000 FW 4.8.0
- partial compatibility for DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.8.0
- partial compatibility for DUE50X0 (DUE5000, DUE5080) FW 4.5.0
See also https://www.emax-tuning.com/eMax-possibilities.pdf
new in version 1.73 (15.04.24):
- partial compatibility for EP801/EP motor firmware 4.2.2
new in version 1.72 (26.03.24):
- partial compatibility for EP801/EP motor firmware 4.2.1
new in version 1.71 (09.02.24):
- partial compatibility for EP801/EP motor firmware 4.2.0
- minor optimizations
new in version 1.70 (23.10.23):
- minor bug fix
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.82 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.82 (31.08.24):
- optimizations and minor bug fixes for DU-EP800
new in version 1.77 (30.06.24):
- partial compatibility for EP801/EP motor firmware 4.3.0
new in version 1.76 (15.06.24):
- new battery types and RS default values for generation 2 added
new in version 1.75 (12.06.24):
- bugfix for DU-E8000 motor firmware 4.10.0
new in version 1.74 (20.05.24):
- partial compatibility for DUEP800 (DUEP800, DUEP800-CRG) FW 4.2.0
- partial compatibility for DUE80X0 (DUE8000, DUE8080) FW 4.10.0
- partial compatibility for DUE7000 FW 4.8.0
- partial compatibility for DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.8.0
- partial compatibility for DUE50X0 (DUE5000, DUE5080) FW 4.5.0
See also https://www.emax-tuning.com/eMax-possibilities.pdf
new in version 1.73 (15.04.24):
- partial compatibility for EP801/EP motor firmware 4.2.2
new in version 1.72 (26.03.24):
- partial compatibility for EP801/EP motor firmware 4.2.1
new in version 1.71 (09.02.24):
- partial compatibility for EP801/EP motor firmware 4.2.0
- minor optimizations
new in version 1.70 (23.10.23):
- minor bug fix
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
1.77
Jun 30, 2024
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.77 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.77 (30.06.24):
- partial compatibility for EP801/EP motor firmware 4.3.0
new in version 1.76 (15.06.24):
- new battery types and RS default values for generation 2 added
new in version 1.75 (12.06.24):
- bugfix for DU-E8000 motor firmware 4.10.0
new in version 1.74 (20.05.24):
- partial compatibility for DUEP800 (DUEP800, DUEP800-CRG) FW 4.2.0
- partial compatibility for DUE80X0 (DUE8000, DUE8080) FW 4.10.0
- partial compatibility for DUE7000 FW 4.8.0
- partial compatibility for DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.8.0
- partial compatibility for DUE50X0 (DUE5000, DUE5080) FW 4.5.0
See also https://www.emax-tuning.com/eMax-possibilities.pdf
new in version 1.73 (15.04.24):
- partial compatibility for EP801/EP motor firmware 4.2.2
new in version 1.72 (26.03.24):
- partial compatibility for EP801/EP motor firmware 4.2.1
new in version 1.71 (09.02.24):
- partial compatibility for EP801/EP motor firmware 4.2.0
- minor optimizations
new in version 1.70 (23.10.23):
- minor bug fix
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.77 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.77 (30.06.24):
- partial compatibility for EP801/EP motor firmware 4.3.0
new in version 1.76 (15.06.24):
- new battery types and RS default values for generation 2 added
new in version 1.75 (12.06.24):
- bugfix for DU-E8000 motor firmware 4.10.0
new in version 1.74 (20.05.24):
- partial compatibility for DUEP800 (DUEP800, DUEP800-CRG) FW 4.2.0
- partial compatibility for DUE80X0 (DUE8000, DUE8080) FW 4.10.0
- partial compatibility for DUE7000 FW 4.8.0
- partial compatibility for DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.8.0
- partial compatibility for DUE50X0 (DUE5000, DUE5080) FW 4.5.0
See also https://www.emax-tuning.com/eMax-possibilities.pdf
new in version 1.73 (15.04.24):
- partial compatibility for EP801/EP motor firmware 4.2.2
new in version 1.72 (26.03.24):
- partial compatibility for EP801/EP motor firmware 4.2.1
new in version 1.71 (09.02.24):
- partial compatibility for EP801/EP motor firmware 4.2.0
- minor optimizations
new in version 1.70 (23.10.23):
- minor bug fix
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
1.76
Jun 16, 2024
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.76 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.76 (15.06.24):
- new battery types and RS default values for generation 2 added
new in version 1.75 (12.06.24):
- bugfix for DU-E8000 motor firmware 4.10.0
new in version 1.74 (20.05.24):
- partial compatibility for DUEP800 (DUEP800, DUEP800-CRG) FW 4.2.0
- partial compatibility for DUE80X0 (DUE8000, DUE8080) FW 4.10.0
- partial compatibility for DUE7000 FW 4.8.0
- partial compatibility for DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.8.0
- partial compatibility for DUE50X0 (DUE5000, DUE5080) FW 4.5.0
See also https://www.emax-tuning.com/eMax-possibilities.pdf
new in version 1.73 (15.04.24):
- partial compatibility for EP801/EP motor firmware 4.2.2
new in version 1.72 (26.03.24):
- partial compatibility for EP801/EP motor firmware 4.2.1
new in version 1.71 (09.02.24):
- partial compatibility for EP801/EP motor firmware 4.2.0
- minor optimizations
new in version 1.70 (23.10.23):
- minor bug fix
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.76 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.76 (15.06.24):
- new battery types and RS default values for generation 2 added
new in version 1.75 (12.06.24):
- bugfix for DU-E8000 motor firmware 4.10.0
new in version 1.74 (20.05.24):
- partial compatibility for DUEP800 (DUEP800, DUEP800-CRG) FW 4.2.0
- partial compatibility for DUE80X0 (DUE8000, DUE8080) FW 4.10.0
- partial compatibility for DUE7000 FW 4.8.0
- partial compatibility for DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.8.0
- partial compatibility for DUE50X0 (DUE5000, DUE5080) FW 4.5.0
See also https://www.emax-tuning.com/eMax-possibilities.pdf
new in version 1.73 (15.04.24):
- partial compatibility for EP801/EP motor firmware 4.2.2
new in version 1.72 (26.03.24):
- partial compatibility for EP801/EP motor firmware 4.2.1
new in version 1.71 (09.02.24):
- partial compatibility for EP801/EP motor firmware 4.2.0
- minor optimizations
new in version 1.70 (23.10.23):
- minor bug fix
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
1.75
Jun 12, 2024
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.75 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.75 (12.06.24):
- bugfix for DU-E8000 motor firmware 4.10.0
new in version 1.74 (20.05.24):
- partial compatibility for DUEP800 (DUEP800, DUEP800-CRG) FW 4.2.0
- partial compatibility for DUE80X0 (DUE8000, DUE8080) FW 4.10.0
- partial compatibility for DUE7000 FW 4.8.0
- partial compatibility for DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.8.0
- partial compatibility for DUE50X0 (DUE5000, DUE5080) FW 4.5.0
See also https://www.emax-tuning.com/eMax-possibilities.pdf
new in version 1.73 (15.04.24):
- partial compatibility for EP801/EP motor firmware 4.2.2
new in version 1.72 (26.03.24):
- partial compatibility for EP801/EP motor firmware 4.2.1
new in version 1.71 (09.02.24):
- partial compatibility for EP801/EP motor firmware 4.2.0
- minor optimizations
new in version 1.70 (23.10.23):
- minor bug fix
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.75 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.75 (12.06.24):
- bugfix for DU-E8000 motor firmware 4.10.0
new in version 1.74 (20.05.24):
- partial compatibility for DUEP800 (DUEP800, DUEP800-CRG) FW 4.2.0
- partial compatibility for DUE80X0 (DUE8000, DUE8080) FW 4.10.0
- partial compatibility for DUE7000 FW 4.8.0
- partial compatibility for DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.8.0
- partial compatibility for DUE50X0 (DUE5000, DUE5080) FW 4.5.0
See also https://www.emax-tuning.com/eMax-possibilities.pdf
new in version 1.73 (15.04.24):
- partial compatibility for EP801/EP motor firmware 4.2.2
new in version 1.72 (26.03.24):
- partial compatibility for EP801/EP motor firmware 4.2.1
new in version 1.71 (09.02.24):
- partial compatibility for EP801/EP motor firmware 4.2.0
- minor optimizations
new in version 1.70 (23.10.23):
- minor bug fix
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
1.74
May 21, 2024
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.74 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.74 (20.05.24):
- partial compatibility for DUEP800 (DUEP800, DUEP800-CRG) FW 4.2.0
- partial compatibility for DUE80X0 (DUE8000, DUE8080) FW 4.10.0
- partial compatibility for DUE7000 FW 4.8.0
- partial compatibility for DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.8.0
- partial compatibility for DUE50X0 (DUE5000, DUE5080) FW 4.5.0
See also https://www.emax-tuning.com/eMax-possibilities.pdf
new in version 1.73 (15.04.24):
- partial compatibility for EP801/EP motor firmware 4.2.2
new in version 1.72 (26.03.24):
- partial compatibility for EP801/EP motor firmware 4.2.1
new in version 1.71 (09.02.24):
- partial compatibility for EP801/EP motor firmware 4.2.0
- minor optimizations
new in version 1.70 (23.10.23):
- minor bug fix
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.74 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.74 (20.05.24):
- partial compatibility for DUEP800 (DUEP800, DUEP800-CRG) FW 4.2.0
- partial compatibility for DUE80X0 (DUE8000, DUE8080) FW 4.10.0
- partial compatibility for DUE7000 FW 4.8.0
- partial compatibility for DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.8.0
- partial compatibility for DUE50X0 (DUE5000, DUE5080) FW 4.5.0
See also https://www.emax-tuning.com/eMax-possibilities.pdf
new in version 1.73 (15.04.24):
- partial compatibility for EP801/EP motor firmware 4.2.2
new in version 1.72 (26.03.24):
- partial compatibility for EP801/EP motor firmware 4.2.1
new in version 1.71 (09.02.24):
- partial compatibility for EP801/EP motor firmware 4.2.0
- minor optimizations
new in version 1.70 (23.10.23):
- minor bug fix
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
1.73
Apr 15, 2024
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.73 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.73 (15.04.24):
- partial compatibility for EP801/EP motor firmware 4.2.2
new in version 1.72 (26.03.24):
- partial compatibility for EP801/EP motor firmware 4.2.1
new in version 1.71 (09.02.24):
- partial compatibility for EP801/EP motor firmware 4.2.0
- minor optimizations
new in version 1.70 (23.10.23):
- minor bug fix
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.73 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.73 (15.04.24):
- partial compatibility for EP801/EP motor firmware 4.2.2
new in version 1.72 (26.03.24):
- partial compatibility for EP801/EP motor firmware 4.2.1
new in version 1.71 (09.02.24):
- partial compatibility for EP801/EP motor firmware 4.2.0
- minor optimizations
new in version 1.70 (23.10.23):
- minor bug fix
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
1.72
Mar 27, 2024
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.72 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.72 (26.03.24):
- partial compatibility for EP801/EP motor firmware 4.2.1
new in version 1.71 (09.02.24):
- partial compatibility for EP801/EP motor firmware 4.2.0
- minor optimizations
new in version 1.70 (23.10.23):
- minor bug fix
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.72 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.72 (26.03.24):
- partial compatibility for EP801/EP motor firmware 4.2.1
new in version 1.71 (09.02.24):
- partial compatibility for EP801/EP motor firmware 4.2.0
- minor optimizations
new in version 1.70 (23.10.23):
- minor bug fix
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
1.71
Feb 9, 2024
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.71 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.71 (09.02.24):
- partial compatibility for EP801/EP motor firmware 4.20
- minor optimizations
new in version 1.70 (23.10.23):
- minor bug fix
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.71 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.71 (09.02.24):
- partial compatibility for EP801/EP motor firmware 4.20
- minor optimizations
new in version 1.70 (23.10.23):
- minor bug fix
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
1.70
Oct 23, 2023
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.70 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.70 (23.10.23):
- minor bug fix
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.70 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.70 (23.10.23):
- minor bug fix
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
1.69
Oct 9, 2023
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.69 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.69 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.69 (09.10.23):
- minor improvements, change of EP801/EP6 message dialog texts
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
1.68
Sep 29, 2023
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.68 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.68 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.68 (29.09.23):
- adaption to DUE50X0 (DUE5000, DUE5080) FW 4.4.10
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
1.67
Sep 11, 2023
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.67 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.67 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.67 (11.09.23):
- bugfix for EP8 (DU-EP800) and new motor firmware 4.1.11
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
1.66
Sep 7, 2023
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.66 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.66 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.66 (07.09.23):
- adaption to DUEP801 (DUEP801, DUEP801-CRG) FW 4.1.1
- adaption to DUEP600 (DUEP600, DUEP600-CRG) FW 4.1.1
- adaption to DUEP800 (DUEP800, DUEP800-CRG) FW 4.1.11
- adaption to DUE80X0 (DUE8000, DUE8080) FW 4.9.5
- adaption to DUE7000 FW 4.7.7
- adaption to DUE61X0 (DUE6100, DUE6100-CRG, DUE6110, DUE6180) & FW 4.7.7
new in version 1.65 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
1.65
Sep 3, 2023
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.65 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.66 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units
new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0
new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0
new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)
new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)
new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)
new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.65 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
The new generation drive units DU-EP801 and DU-E600 as well as its variants RS and CRG are partially supported now
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.66 (02.09.23):
- EP801/EP6 change of max. peak power and max. torque range added
- EP801/EP6 "reduced max. speed setting" enabled and enhanced
- EP801/EP6 "motor angle setting" enabled
- SC-EN500 display added
- new cassette types added (just for reading)
- correction in EP8xx performance view site with jump to next edit field
- bugfix: display speed adjustment value was unintentionally jumping from max. value +5,0 back to -5,0 when pressing forward button
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units
new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0
new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0
new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)
new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)
new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)
new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo
1.63
Apr 1, 2023
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.63 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units
new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0
new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0
new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)
new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)
new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)
new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo
new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0
new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8
ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added
ver. 1.42 (17.04.21):
- new battery type BT-E8016 added
ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.63 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.63 (31.03.23):
- update to newest firmware version 4.4.9 for DUE50X0
- update to newest firmware version 4.7.6 for DUE61X0 & DUE7000
- update to newest firmware version 4.1.10 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units
new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0
new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0
new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)
new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)
new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)
new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo
new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0
new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8
ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added
ver. 1.42 (17.04.21):
- new battery type BT-E8016 added
ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)
1.62
Mar 21, 2023
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.62 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units
new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0
new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0
new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)
new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)
new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)
new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo
new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0
new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8
ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added
ver. 1.42 (17.04.21):
- new battery type BT-E8016 added
ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)
ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.62 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.62 (21.03.23):
- minor optimizations and bug fixes
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units
new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0
new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0
new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)
new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)
new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)
new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo
new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0
new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8
ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added
ver. 1.42 (17.04.21):
- new battery type BT-E8016 added
ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)
ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved
1.61
Mar 3, 2023
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.61 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units
new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0
new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0
new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)
new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)
new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)
new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo
new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0
new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8
ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added
ver. 1.42 (17.04.21):
- new battery type BT-E8016 added
ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)
ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.61 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.61 (02.03.23):
- minor optimizations and bug fixes
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units
new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0
new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0
new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)
new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)
new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)
new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo
new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0
new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8
ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added
ver. 1.42 (17.04.21):
- new battery type BT-E8016 added
ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)
ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved
1.59
Feb 26, 2023
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.59 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units
new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0
new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0
new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)
new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)
new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)
new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo
new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0
new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8
ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added
ver. 1.42 (17.04.21):
- new battery type BT-E8016 added
ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)
ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.59 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 display types, EW-EN100 cockpit as well as the SW-EN600-L unit.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.59 (26.02.23):
- new battery types, Shimano STePS components and destination settings added
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units
new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0
new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0
new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)
new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)
new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)
new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo
new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0
new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8
ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added
ver. 1.42 (17.04.21):
- new battery type BT-E8016 added
ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)
ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved
1.58
Oct 28, 2022
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.58 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 and EW-EN100 display types.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units
new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0
new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0
new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)
new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)
new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)
new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo
new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0
new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8
ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added
ver. 1.42 (17.04.21):
- new battery type BT-E8016 added
ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)
ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved
1.066
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.58 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 and EW-EN100 display types.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.58 (28.10.22):
- corrections for display speed adjustment (special settings)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units
new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0
new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0
new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)
new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)
new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)
new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo
new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0
new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8
ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added
ver. 1.42 (17.04.21):
- new battery type BT-E8016 added
ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)
ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved
1.066
1.57
Oct 19, 2022
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.57 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 and EW-EN100 display types.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units
new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0
new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0
new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)
new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)
new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)
new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo
new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0
new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8
ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added
ver. 1.42 (17.04.21):
- new battery type BT-E8016 added
ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)
ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved
1.066
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.57 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 and EW-EN100 display types.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.57 (18.10.22):
- update to newest firmware version 4.4.8 for DUE50X0
- update to newest firmware version 4.7.5 for DUE61X0 & DUE7000
- update to newest firmware version 4.9.4 for DUE80X0
- update to newest firmware version 4.1.9 for DUEP800 (EP8, EP8-CRG. EP8-RS)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units
new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0
new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0
new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)
new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)
new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)
new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo
new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0
new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8
ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added
ver. 1.42 (17.04.21):
- new battery type BT-E8016 added
ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)
ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved
1.066
1.56
Oct 17, 2022
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.56 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 and EW-EN100 display types.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units
new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0
new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0
new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)
new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)
new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)
new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo
new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0
new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8
ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added
ver. 1.42 (17.04.21):
- new battery type BT-E8016 added
ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)
ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved
1.066
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.56 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 and EW-EN100 display types.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.56 (17.10.22):
- new battery types added
- change of EP8 profile OEM default settings added
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units
new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0
new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0
new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)
new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)
new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)
new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo
new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0
new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8
ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added
ver. 1.42 (17.04.21):
- new battery type BT-E8016 added
ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)
ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved
1.066
1.55
Oct 1, 2022
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.55 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 and EW-EN100 display types.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units
new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0
new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0
new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)
new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)
new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)
new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo
new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0
new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8
ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added
ver. 1.42 (17.04.21):
- new battery type BT-E8016 added
ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)
ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved
1.066
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.55 for STEPS drive units is capable to communicate with the SC-EM800, SC-E8000, SC-E7000, SC-E6100 and EW-EN100 display types.
Additionally to DU-E80X0 motors, now DU-EP800, DU-E7000, DU-E6XXX and DU-E50X0 drive units are supported too.
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DU-E80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.55 (01.10.22):
- display speed adjustment
- torque range min. value added
- improvements and indication for special EP8 types
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units
new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0
new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0
new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)
new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)
new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)
new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo
new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0
new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8
ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added
ver. 1.42 (17.04.21):
- new battery type BT-E8016 added
ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)
ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved
1.066
1.54
Jul 10, 2022
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.54 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DUE80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units
new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0
new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0
new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)
new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)
new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)
new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo
new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0
new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8
ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added
ver. 1.42 (17.04.21):
- new battery type BT-E8016 added
ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)
ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.54 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DUE80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.54 (10.07.22):
- bugfix for changing cassette type on some drive units
new in version 1.53 (08.07.22):
- minor fixes (darkmode & typo)
new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units
new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0
new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0
new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)
new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)
new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)
new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo
new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0
new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8
ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added
ver. 1.42 (17.04.21):
- new battery type BT-E8016 added
ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)
ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved
1.53
Jul 9, 2022
TAKE CARE: For increasing motor max. support speed an additional license key is necessary! See also www.eMax-Tuning.com.
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.53 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DUE80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.53 (08.07.22):
-minor fixes (darkmode & typo)
new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units
new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0
new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0
new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)
new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)
new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)
new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo
new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0
new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8
ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added
ver. 1.42 (17.04.21):
- new battery type BT-E8016 added
ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)
ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved
TAKE CARE: This version is not able to increase max. motor support with the latest motor firmware versions from Shimano!
Please have a look on the news section of www.eMax-Tuning.com/home-en#news for possibilities or contact us via info@eMax-Tuning.com.
This version 1.53 for STEPS drive units is capable to communicate with the SCE8000, SCE7000, SCE6100 and EW-EN100 display types.
Additionally to DUE80X0 motors, now DUEP800, DUE7000, DUE6XXX and DUE50X0 drive units are supported too.
All "motor performance settings" and "special settings" (change of gear type, chainring & smallest rear sprocket size, remaining light time) could be used in the license free version.
Special to DUE80X0 drive units:
With motor firmware equal or above 4.7.0 it is only possible to set the motor performance settings up to 300% assist ratio and torque to 70Nm.
(with motor firmware 4.2.7 - 4.6.1, the max. assist ratio value could be set 500%)
(with motor firmware 4.2.7 - 4.6.1 AND a valid license key the max. torque could be increased to 75Nm, max. peak power also would be increased then to 550W instead of standard 500W)
new in version 1.53 (08.07.22):
-minor fixes (darkmode & typo)
new in version 1.52 (20.06.22):
- gear mode configuration expanded to hubs (Alfine / Nexus)
- gear mode configuration accessible for all drive units
new in version 1.51 (29.03.22):
- update to newest firmware versions 4.4.7 for DUE50X0
new in version 1.50 (15.03.22):
- update to newest firmware versions 4.7.4 for DUE61X0 & DUE7000
- update to newest firmware versions 4.9.3 for DUE80X0
new in version 1.49 (22.02.22):
- 32 teeth chainring size added for DUEP800 (EP8)
new in version 1.48 (24.12.21):
- update to newest firmware versions 4.1.8 for DUEP800 (EP8)
new in version 1.47 (25.11.21):
- update to newest firmware versions 4.1.7 for DUEP800 (EP8)
new in version 1.46 (18.11.21):
- optimization for EP8-RS
- typo
new in version 1.45 (07.09.21):
- update to newest firmware versions 4.1.6 for DUEP800 (EP8) & 4.4.5 for DUE50X0
new in version 1.44 (03.06.21):
- update to newest firmware version 4.1.5 for EP8
ver. 1.43 (05.05.21):
- chainring & rear sprocket size for DUE5xxx and DUE6xxx added
ver. 1.42 (17.04.21):
- new battery type BT-E8016 added
ver. 1.41 (11.04.21):
- new battery types added
- bugfix (profile 2 EP8-RS default translation error)
ver. 1.40 (06.04.21):
- update to firmware 4.4.4 for DUE50X0 (DUE5000, DUE5080)
- update to fw. 4.7.2 for DUE61X0 (DUE6100, DUE6110, DUE6180)
- update to fw. 4.7.2 for DUE7000
- update to fw. 4.1.4 for EP8
- profiles added for EP8/EP8-RS
- reduced max. speed for EP8 added
- smallest sprocket for EP8 set to 10 (instead of 11)
- dark mode issue on light settings solved
eMaxMobileApp FAQ
Click here to learn how to download eMaxMobileApp in restricted country or region.
Check the following list to see the minimum requirements of eMaxMobileApp.
iPhone
Requires iOS 12.0 or later.
iPad
Requires iPadOS 12.0 or later.
iPod touch
Requires iOS 12.0 or later.
eMaxMobileApp supports English